REQUEST A QUOTE / ENQUIRY FORM
Universal Transducer Adapters
Easily Adapt Your Vantage System to Work with a Range of Transducers
The Verasonics' Universal Transducer Adapter (UTA) makes it easy to adapt your Vantage System to work with transducers with different connectors. Switching between UTAs is quick and simple, taking only a few minutes. Simply loosen a set of screws, change the UTA, and re-tighten the screws. The Vantage system must be shut down before and rebooted after the UTA changeover.
One UTA adapter is included with the purchase of any Vantage system. Additional adapters are available to meet changing research needs, and older Vantage systems can be upgraded to the latest UTA technology.
Key Benefits of the UTA:
- Use high-performance, low-noise connectors
- Connect transducers with up to 256 elements without a multiplexer
- Provide signal paths for probes requiring additional grounding, power supply, digital control signals, etc.
- Retain compatibility with Verasonics transducers, as well as transducers from a variety of supplier partners
REQUEST A QUOTE
Biomedical Research
The UTA 260-S has a single 260 pin connector and is available on the Vantage 128 and Vantage 64 LE.
The UTA 260-D has two 260 pin connectors and is available on the Vantage 256. Each connector provides
signals for 128 channels.
These adapters provide compatibility with many Verasonics transducers and most refurbished HDI transducers
manufactured by ATL Ultrasound.
The UTA 408-GE supports selected transducers from GE Healthcare, certain Verasonics transducers that
use the GE pinout model, as well as custom probes using the GE 408 Backshell Kit. It is available on
the Vantage 256, Vantage 128, and Vantage 64 LE.
The UTA 408 uses Verasonics’ pinout and is available on the Vantage 256 only. It allows direct connectivity
for transducers with up to 256 elements without a multiplexer. The additional contacts provide grounding,
digital signal control paths, and more
The UTA 360 is available on the Vantage 256 and provides compatibility with the MS-series of transducers
from VisualSonics. These high frequency transducers have 256 elements, which are directly connected to the
256 channels through this adapter.
These transducers are compatible with Vantage high-frequency configurations
With up to 128 connectors for single element transducers, the UTA 128 LEMO and the UTA 64 LEMO adapters enable evaluation of new transducers and interrogation of complex structures. 2 LEMO to BNC adapters are included.
For users of Ultrasonix transducers the UTA 156-U provides compatibility between Vantage systems and selected Sonix transducers.
UTA 256 Direct is a simple and low-cost method to directly connect transducers with up to 256 elements
to a Vantage system without the use of a multiplexer. Requires soldering micro-coax wires to termination boards.
The Vantage 32 LE system and the Vantage 64 system can operate standard Verasonics transducers with
up to 128 elements when the UTA 260-MUX is used.
For research in 3D and volume acquisition techniques, the UTA 1024-MUX adapter provides support to operate matrix array transducers with up to 1024 elements. Transducers are available from Vermon and other leading transducer manufacturers.
NDE/NDT Research
The UTA 128 LEMO adapter provides direct transmit and/or receive channel connections for up
to 128 single element transducers. 2 LEMO to BNC adapters are included.
The UTA 64 LEMO adapter provides direct transmit and/or receive channel connections for up
to 64 single element transducers. 2 LEMO to BNC adapters are included.
The UTA 160-DH/32 LEMO adapter provides 2 Hypertronics 160-pin connectors in addition to
32 single-channel LEMO connectors. This UTA is available on all Vantage systems.
The UTA 160-SH/8 LEMO adapter provides a single Hypertronics 160-pin connector in addition to 8 single-channel LEMO connectors.
The UTA 160-SI/8 LEMO/ adapter has one I-PEX phased array connector and 8 single-channel LEMO connectors.